FREE ELECTRONIC LIBRARY - Abstract, dissertation, book

Pages:   || 2 |

«Installation Guide Introduction Model FR114P ProSafe Firewall with Print Server Thank you for purchasing a NETGEAR FR114P Cable/DSL ProSafe Firewall ...»

-- [ Page 1 ] --

Cable/DSL ProSafe Firewall

with Print Server MODEL FR114P

Installation Guide


Model FR114P ProSafe Firewall with Print Server

Thank you for purchasing a NETGEAR FR114P Cable/DSL ProSafe Firewall with Print Server.

A firewall is a special type of router that incorporates features for network security. With this

firewall you can have secure Internet access through a high-speed DSL or cable modem and share

the single modem with several computers. The FR114P also incorporates a built-in print server.

This installation guide shows you how to connect the firewall and configure it and your computers for secure Internet access. Setup is easy—follow the instructions in this guide and your system will be up and running quickly.

If you have problems, there is a troubleshooting section on page 13 to help you—or you can get more detailed troubleshooting information from the Reference Manual on the CD, online from www.NETGEAR.com or by phone.

Installation Overview Estimated time: 15 to 30 minutes

1. Gather the configuration information you have for your working DSL or cable modem connection to the Internet.

2. Install the firewall between the DSL or cable modem and one computer.

3. Configure that computer to work with the firewall and restart the computer and modem.

4. Configure the firewall and go online to test the connection.

5. Connect other computers, configure them and restart each. (optional)

6. Configure for using the print server. (optional) On the FR114P Resource CD, you’ll find the FR114P Installation Assistant, which supplements the instructions in this installation guide by animating the step-by-step procedures given here.

For more detailed information about installation, troubleshooting and configuration procedures, see the Reference Manual on the CD.

What’s in the Box Model FR114P ProSafe Firewall with Print Server Power adapter FR114P Resource CD, installation guide, support Category 5 information card & 100 Mbps warranty/registration card Ethernet cable When you open the box, verify that you received everything.

The package includes:

• FR114P Cable/DSL ProSafe Firewall with Print Server

• AC power adapter

• Ethernet patch cable

• FR114P Resource CD, including a full Reference Manual and Installation Assistant.

• FR114P Installation Guide (this document)

• Warranty and registration card

• Support information card If you don’t have everything listed above, see the support information card for contact information. If the support information card is missing, you can get contact information at www.NETGEAR.com in the Customer Service area.

–  –  –

• TCP/IP installed.

• If your computer is a Windows® computer, it must have the Client for Microsoft® Networks software installed.

Note: Please see the Reference Manual on the CD if you need help installing TCP/IP software or the Client for Microsoft Networks software on any Windows computer that hasn’t been networked previously.

• A Category 5 (Cat 5) Ethernet patch cable Note: There is one cable in the box with the firewall.

Connection information Later in the setup process you’ll need to configure the firewall to work with your network. A Setup Wizard is available to help you through this procedure. You can configure the firewall yourself using information that you can get from your computer or your ISP about your current Internet connection.

The next page includes blanks for you to fill in and refer to later. To get the needed

information from your computer:

• Open the Network control panel, select the TCP/IP entry, and click Properties.

(Windows 98/Me)

• Open Local Area Network Connection and click Properties. (Windows 2000/XP)

• Open the TCP/IP (or Network) control panel. (Macintosh®) Your ISP should have provided you with a summary sheet of all the information needed to connect your computer to the Internet. If you cannot locate the information, you’ll have to contact your ISP.

An ISP Guide is included with your firewall’s documentation, either as a printed card or on the Resource CD. The ISP Guide contains specific configuration guidelines for connecting to many popular ISPs.

Host and Domain Names Some ISPs use a specific host or domain name—like jsmith or earthlink.net. If you haven’t been given specific information about host or domain names then use the following examples

as a guide:

• If your main e-mail account with your ISP is aaa@yyy.com, then use aaa as your host name. (Your ISP might call this your account name, user name, or system name.)

• If your ISP’s mail server is mail.xxx.yyy.com, then use xxx.yyy.com as the domain name.

Host name:_____________________________________

Domain name: __________________________________

Login Name If your ISP requires a login name and password (possibly because you have a PPPoE account),

fill in the following:

Login name:____________________________________

(may be your full e-mail address) Password:______________________________________

Note: The login name could be called a user name or account name by your ISP.

The login name is case sensitive. You must type it exactly as given by your ISP. For example, c_jones is a different login name than C_Jones or cjones.

Fixed (or static) IP address

If you have a static IP address through your ISP, fill in the following information:

IP address: _____._____._____._____ Subnet mask: _____._____._____._____ Gateway IP address:_____._____._____._____ DNS server address information

If you were given specific Domain Name System (DNS) server addresses, fill in the following:

DNS Server IP address(es): _____._____._____._____ _____._____._____._____ Install the Firewall After unpacking the box and locating the configuration information, you’re ready to install the firewall.

Note: You do not have to power down any equipment to do this, but if you need to move your computers (perhaps to get to ports in the back), you may want to shut down the computers before moving them around.

–  –  –

DSL or cable modem to your firewall since this may be a special cable even though it Model FR114P ProSafe Firewall with Print Server looks like other LAN cables.

2. Remove this cable from the computer and insert that end into the Internet port on the rear panel of the firewall.

3. Use the Ethernet patch cable that came with the firewall to connect the computer to one of the four numbered local Ethernet ports on the rear panel of the firewall.

4. Connect the power adapter’s cord into the back of the firewall and then plug the adapter into a power source (such as a wall socket or power strip).

Note: If you want to connect other computers to the firewall, don’t connect them now. Do that after you know that the modem/firewall setup works with one computer.

Check the setup

• The Test light turns on for a few seconds and then goes off.

Note: If the Test light remains on for more than one minute, go to Troubleshooting on page 13.

• The Power and Internet Link lights should be lit.

• If your computer is on, the Local Link light should be on for the port number that your computer is connected to.

Note: If the port connection is a 100 Mbps connection, the 100 light should be on.

If either the Power, Internet Link, or Local port Link light isn’t lit, go to Troubleshooting on page 13.

3 Configure the Computer to Work with the Firewall and Restart the Network Next, make sure that the computer can interact with the firewall. To do this, configure the TCP/IP settings on the computer and then restart the network. How you do this depends on your computer.

Windows Operating System Normally, you can leave the TCP/IP setup parameters at their factory default settings unless you have a specific reason to change them. You should verify that the computer is set to ‘obtain an IP address automatically’ in the Network control panel.

Windows 98 or Me

1. Choose SettingsControl Panel from the Start menu.

2. Double-click the Network icon.

3. Click the Configuration tab.

4. In the list of installed network components, select the TCP/IP entry for the computer’s Ethernet adapter or NIC.

5. Click Properties.

6. Click the IP Address tab.

7. Check that Obtain an IP Address Automatically ia selected, select if not.

8. Click the Gateway tab.

9. Select and remove any IP Gateway addresses that are listed.

10. Click OK and click OK again to close the Network control panel.

11. Go to Restarting the Network on the next page.

Windows 2000 or XP

–  –  –

1. Choose Control Panels TCP/IP from the Apple menu.

2. If not already selected, select Ethernet in the Connect via list.

3. Select Using DHCP Server in the Configure list.

4. Click the close box.

5. If asked if you want to save this configuration, click Save.

6. Go to Restarting the Network.

Mac OS X

1. Choose System Preferences from the Apple menu.

2. Double-click Network.

3. If not already selected, select Built-in Ethernet in the Configure list.

4. If not already selected, select Using DHCP in the TCP/IP tab.

5. Click Save.

6. Go to Restarting the Network.

Linux® or UNIX® Operating System If you’re installing the firewall with a Linux-based or UNIX-based computer see your system documentation for TCP/IP and networking setup information.

Restarting the Network Once you’ve set up your computer to work with the firewall, you must reset the network for the devices to be able to communicate correctly.

1. Turn off the DSL or cable modem, wait 15 seconds, and then turn it on again.

Note: If the modem doesn’t have an on/off switch, either pull the modem’s power adapter out of the wall socket or power down the power strip.

2. If the firewall was powered down, power it up again and wait until the Test light turns off.

3. Restart the computer that is connected to the firewall.

4 Configure the Firewall and Test the Connection Now you configure the firewall to work with your DSL or cable connection. You configure your firewall using Internet browser software such as Microsoft® Internet Explorer 5.0 or Netscape Navigator® 4.7 or later. You can either use the Setup Wizard or configure the firewall manually.

1. Start a browser on the computer connected to the firewall.

2. In the Address or Location box, type and press Enter or Return.

Note: You may want to bookmark this address in your browser for handy access in the future.

3. In the User Name box, type admin

4. In the Password box, type password Note: The User Name and Password are case sensitive.

5. Click OK. The firewall’s Setup Wizard page appears. If not, select setup wizard from the bar on the left.

6. To have the Setup Wizard automatically configure the firewall, click Yes, click Next and follow the instructions on screen. To configure it manually, click No, then click Next and continue with the steps listed here.

7. Fill in the form on the Basic Settings page. (Refer to page 4 where you filled in the information previously.) Note: Helpful information appears on the right side of the page to assist you as you fill in the form.

8. Click Apply to have your information sent to the firewall.

Test the Connection

1. Click the Test button on the Basic Settings page.

This should open a new browser window and take you to NETGEAR’s Web site (www.NETGEAR.com).

Note: If NETGEAR’s Web site doesn’t appear, go to Troubleshooting on page 13.

2. Close the browser window showing NETGEAR’s home page.

3. Click the Logout button on the left navigation area.

5 Connect and Configure Other Computers (Optional) Now that you have one computer set up to access the Internet through the firewall, you can connect other computers so they can share the modem.

1. Connect a Category 5 Ethernet patch cable between another computer and one of the remaining numbered Local ports on the firewall.

2. Check to make sure that the associated port number’s Link light is lit. The light flashes when data is being transferred over the connection.

–  –  –

Note: If the numbered Link light isn’t lit, go to Troubleshooting on page 13.

3. Go back to Installation Step 3 (pages 8 and 9) and go through the sequence of steps applicable for each computer.

4. Restart each computer.

5. Test each computer’s connection by going to NETGEAR’s Web site (www.NETGEAR.com) from each computer.

Note: If you have more than 4 computers or devices to connect to this firewall, you must connect them to a hub or switch (such as the NETGEAR 8-port Fast Ethernet Switch) and then connect the hub or switch to the firewall. Connect the other hub or switch to Port 4 of the FR114P and press the Uplink button. If Port 4’s Link light is not lit, change the Uplink button to the other position and check the Link light again.

By using hubs or switches, you may connect up to 253 computers to the firewall.

Optional Configurations Using the Printer Server (Optional) To use the Model FR114P’s Print Server, your computer must have a network printing driver installed, and you must add the printer to the computer’s list of known printers. The procedure depends on your PC’s operating system.

Windows 95/98/ME, Windows NT 4.0, Windows 2000/XP For Windows network printing, you can either use Windows Peer to Peer (PTP) or Line Printer Remote (LPR) protocol. You can install driver software from the FR114P Resource CD. Please refer to the Reference Manual on the FR114P Resource CD.

Pages:   || 2 |

Similar works:

«jobbörse siegen jobbörse siegen Erstklassige Jobs Siegen | jobware.de Ihren Top-Job in Siegen finden Sie hier! Jobware.de Jobbörse Aktuelle Stellenangebote finden. Die Nr. Aktuelle Stellenangebote finden. Die Nr. 1, wenn es um Jobs geht Jobsuche in Siegen | jobworld.de Über 400.000 freie Jobs: Jetzt in Echtzeit suchen! Jobs in Ihrer Umgebung | indeed.de Tausende Stellen von Job-Sites mit nur einer Suche. Siegen Jobs, Stellenangebote Siegen, Stellenmarkt Siegen Siegen Jobbörse mit...»

«Gegenständliche Modellierung virtueller Informationswelten Eva Hornecker und Kai Schäfer Forschungszentrum Arbeit und Technik (artec), Universität Bremen Veröffentlicht in: Software Ergonomie ´99, U. Arend, E. Eberleh, K. Pitschke (Hrsg.), Teubner, Stuttgart, 1999 Zusammenfassung In diesem Beitrag stellen wir ein Konzept greifbarer, gegenständlicher Benutzungsschnittstellen vor. Es werden Übergänge zwischen dem Modellieren im Realen und dem Erstellen virtueller Modelle geschaffen....»

«A Reappraisal of Online Mathematics Teaching Using L TEX A Eamon Costello1, Elaine Walsh1, and Seamus Fox1 Oscail, Distance Education Centre, Dublin City University eamon.costello@dcu.ie elaine.walsh@dcu.ie seamus.fox@dcu.ie Abstract. The mathematics language L TEX is often seen as a legacy A technology that is awkward to use. MathML a verbose language designed for data-exchange, and to be written and understood by machines is by contrast seen as something that will aid online mathematics and...»

«Systems Engineering Education Development (SEED) Case Study Thirteenth Annual International Symposium of the International Council On Systems Engineering (INCOSE) 29 June to 3 July 2003 Raymond L. Granata Thomas C. Bagg, I11 QSS Group, Inc. QSS Group, Inc. 7404 Executive Place, Suite 400 7404 Executive Place, Suite 400 Seabrook, MD 20706 Seabrook, MD 20706 30 1-867-0143 301-867-0063 rgranata@qssmeds.com tbagg@qssmeds.com Carolyn A. Casey Mark D. Brumfield NASA Goddard Space Flight Center Acting...»

«“Everything you always wanted to know about EDM fluid. but were too afraid to ask.” FLASH POINT: ASTM D92-52 (CLEVLAND OPEN CUP) When a liquid petroleum product is exposed to air, some of it evaporates, causing a certain vapor/air concentration. As the temperature of the liquid product is raised more and more evaporates and the vapor/air ratio increases. Eventually, a temperature is reached at which the vapor air ratio is high enough to support momentary combustion, if a source of ignition...»

«Александр Иванович Введенский как логик. Часть I Б. В. Бирюков, Л. Г. Бирюкова abstract. The paper is devoted to the logical ideas and the biography of the promonent Russian thinker Alexander Ivanovich Vvedenskiy (1856– 1925). Ключевые слова: А.И. Введенский, история логики, философская логика Александр Иванович Введенский (1856–1925) —...»

«Как получить европейский патент 12-ое издание июнь 2009 Руководство для заявителей European Patent Office (EPO) Часть 1 Vienna The Hague Munich Rennweg 12 Patentlaan 2 Headquarters 12-ое издание 1030 Vienna 2288 EE Rijswijk Erhardtstr. 27 июнь 2009 Austria Netherlands 80469 Munich Tel. +43 (0)1 52126-0 Tel. +31 (0)70 340-2040 Germany Postal address Postal address Tel. +49 (0)89 2399-0 Postfach 90 Postbus 5818...»

«Departement der Geowissenschaften Universität Freiburg (Schweiz) Alterspolitik in Schweizer Gemeinden Netzwerke, politische Aufgaben und Planungspraktiken DISSERTATION zur Erlangung der Würde eines Doctor rerum naturalium der Mathematisch-Naturwissenschaftlichen Fakultät der Universität Freiburg in der Schweiz vorgelegt von Christina Zweifel aus Glarus Dissertation Nr: 1779 UniPrint Danksagungen Ich bedanke mich herzlich bei Joris Van Wezemael für die Betreuung meiner Dissertation, bei der...»

«Assessor’s guidelines for the SVQs in Amenity Horticulture at levels 2 and 3 and Amenity Horticulture Management at level 4 First edition: January 2003 Second edition: May 2008 Publication code: DB1772/2 Published by the Scottish Qualifications Authority The Optima Building, 58 Robertson Street, Glasgow, G2 7DQ, and Ironmills Road, Dalkeith, Midlothian, EH22 1LE The information in this publication may be reproduced in support of SQA qualifications. If it is reproduced, SQA should be clearly...»

«УДК 372.881.161.1 Сичинава Юлия Николаевна Sichinava Yulia Nikolayevna кандидат филологических наук, PhD (Philology), Assistant Professor, доцент кафедры русского языка Russian Language Subdepartment, Военного учебно-научного центра Air Force Academy Военно-воздушных сил «Военно-воздушная академия им. профессора Н.Е....»

«Title Embedding the personal: the construction of a 'fashion autobiography' as a museum exhibition, informed by innovative practice at ModeMuseum, Antwerp Type Thesis URL http://ualresearchonline.arts.ac.uk/5688/ Date 2012 Citation Horsley, Jeffrey (2012) Embedding the personal: the construction of a 'fashion autobiography' as a museum exhibition, informed by innovative practice at ModeMuseum, Antwerp. PhD thesis, University of the Arts London. Creators Horsley, Jeffrey Usage Guidelines Please...»

«Mitteilung 5. November 2015 Zurich erzielt in den ersten neun Monaten 2015 einen Betriebsgewinn von USD 2,5 Mrd. – das Ergebnis in der Schadenversicherung liegt im Rahmen der Vorabinformation  Betriebsgewinn (BOP) im 3. Quartal von USD 256 Mio., ein Rückgang um 79% im Vorjahresvergleich; Rückgang des BOP für die ersten neun Monate um 35% auf USD 2,5 Mrd.  Den Aktionären zurechenbarer Reingewinn nach Steuern (NIAS) im 3. Quartal von USD 207 Mio., ein Rückgang um 79% im...»

<<  HOME   |    CONTACTS
2016 www.abstract.xlibx.info - Free e-library - Abstract, dissertation, book

Materials of this site are available for review, all rights belong to their respective owners.
If you do not agree with the fact that your material is placed on this site, please, email us, we will within 1-2 business days delete him.